PAUT066E.zip

;-------------------------------------------------------------------------

; Revision V0.00
; - First release
;
; Revision V1.00
; - Added config support for Belt Scale 12/03/2002
; - Changed Max_Input_Len from 5 to 20
; - Changed Max_Data_Len from 5 to 20
;
; Revision V2.00
; - Added alternate config modules for Unipro 28/05/2003
;------------------------------------------------------------------------- 

; Revision V0.00
; - First release
;
; Revision V1.00
; - Added config support for Belt Scale 12/03/2002
; - Changed Max_Input_Len from 5 to 20
; - Changed Max_Data_Len from 5 to 20
;
; Revision V2.00
; - Added alternate config modules for Unipro 28/05/2003
;
;-------------------------------------------------------------------------
#Profibus_DP
GSD_Revision        = 3
Vendor_Name         = "Process Automation (PTY)"
Model_Name          = "PROFI200-PA"
Revision            = "V2.00"
Ident_Number        = 0x066E
Protocol_Ident      = 0
Station_Type        = 0
FMS_supp            = 0
Hardware_Release    = "-"
Software_Release    = "-"
;
Implementation_Type = "DPC31"
;Bitmap_Device       = ""
;Bitmap_Diag         = ""
;Bitmap_SF           = ""
;
31.25_supp          = 1
45.45_supp          = 1
93.75_supp          = 1
MaxTsdr_31.25       = 100
MaxTsdr_45.45       = 250
MaxTsdr_93.75       = 1000
;
Redundancy          = 0
Repeater_Ctrl_Sig   = 0
24V_Pins            = 0
Freeze_Mode_supp    = 0
Sync_Mode_supp      = 0
Set_Slave_Add_supp  = 1
;
Slave_Family        = 12
Min_Slave_Intervall = 250
Modular_Station     = 1
Max_Module          = 1
Max_Input_Len       = 20
Max_Output_Len      = 0
Max_Data_Len        = 20
Max_Diag_Data_Len   = 14
;
Max_User_Prm_Data_Len = 3
Ext_User_Prm_Data_Const(0) = 0x00, 0x00, 0x00
;
Physical_Interface = 0                     ; RS-485 Standard Copper
Transmission_Delay_45.45 = 0
Reaction_Delay_45.45     = 0
Transmission_Delay_93.75 = 0
Reaction_Delay_93.75     = 0
End_Physical_Interface
;
Physical_Interface = 1                     ; IEC61158-2
Transmission_Delay_31.25 = 0
Reaction_Delay_31.25     = 0
End_Physical_Interface
;
;-------------------------------------------------------------------------
Unit_Diag_Bit(16)   = "Error appears"
Unit_Diag_Bit(17)   = "Error disappears"
Unit_Diag_Bit(24)   = "Hardware failure electronics"
Unit_Diag_Bit(25)   = "Hardware failure mechanics"
Unit_Diag_Bit(26)   = "Motor temperature too high"
Unit_Diag_Bit(27)   = "Electronic temperature too high"
Unit_Diag_Bit(28)   = "Memory error"
Unit_Diag_Bit(29)   = "Measurement failure"
Unit_Diag_Bit(30)   = "Device not initialized"
Unit_Diag_Bit(31)   = "Device initialization failed"
Unit_Diag_Bit(32)   = "Zero point error"
Unit_Diag_Bit(33)   = "Power supply failed"
Unit_Diag_Bit(34)   = "Configuration invalid"
Unit_Diag_Bit(35)   = "Restart"
Unit_Diag_Bit(36)   = "Coldstart"
Unit_Diag_Bit(37)   = "Maintenance required"
Unit_Diag_Bit(38)   = "Characteristics invalid"
Unit_Diag_Bit(39)   = "Ident_Number violation"
Unit_Diag_Bit(55)   = "Extension Available"
;
;-------------------------------------------------------------------------
;           "12345678901234567890123456789012"
;Modules for Analog Input
Module    = "Analog Input (AI)short"    0x94
1
EndModule
;Modules for Analog Input
Module    = "Analog Input (AI)long"     0x42,0x84,0x08,0x05
2
EndModule
;Modules for Unipro
Module    = "Unipro Inputs"             0xD9
3
EndModule
;Module for Unipro
Module    = "Two Analog Inputs (AI)"    0x94,0x94
4
EndModule
;Module for Unipro
Module    = "Three Analog Inputs (AI)"  0x94,0x94,0x94
5
EndModule
;Module for Unipro
Module    = "Four Analog Inputs (AI)"   0x94,0x94,0x94,0x94
6
EndModule
;
;-------------------------------------------------------------------------
;-------------------------------------------------------------------------
;-------------------------------------------------------------------------